User manual DEI MCB1000 Installation Guide

[. . . ] NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with these UNITS. All components other than the unit, including and without limitation the remote control, cables and installation accessories, carry a 60-day warranty from the date of purchase of the same. [. . . ] Mounting Screws x 4. Note: This manual makes reference to optional Directed Video parts not included with this product. 6 © 2001 Directed Electronics, Inc. Universal Remote Control REMOTE CONTROL OPERATION 1. FM MOD - Turns the power to the RFM100 FM modulator on/off if connected to the MCB1000 FM modulator control output. ZONE BUTTONS - Selects which monitor zone of the MCB1000 the remote control will operate. MENU/ADJUST BUTTONS - Accesses the setup menu and hardware programming menus for the MCB1000. 4. 5. NOTE: Refer to the On-screen Programming section for programming information. 6. VCR CONTROL - Controls the basic functions of the VCR. REMOTE CONTROL BATTERY INSTALL/REPLACE 1. Refer to the programming menu to change from Antenna to CATV. © 2001 Directed Electronics, Inc. 8 VCR CONTROLS BUTTONS The VCR control buttons (9) will operate Directed video's VC2010 and VC2050 Video Cassette Recorders I I I I I PWR button - Turns the VCR power on/off RR button Press in stop mode to fast rewind the tape. Play button - Press to begin tape playback I Press again to resume normal tape playback Press repeatedly when tape is paused to advance one frame at a time. Press and hold when tape is paused for three seconds to activate slow motion playback ON-SCREEN PROGRAMMING The MCB1000 hardware functions and on-screen display can be customized at the time of installation. On-screen programming is only available when integrating with Directeds HVM500, RVM560, RVM680 and RVM700 video monitors. For a complete guide to On-screen Programming see the Owner/Installation guide for your Directed Video Monitor. The Expanded Menu switch on the MCB1000 module must be on for the Setup Menu to appear on screen. Please use the Hardware Options Menu below for more information. I I FF button Press to fast-forward the tape when in stop mode. CN/TRK buttons I I I I Press to manually adjusts tape tracking when in play mode. Stop button - Press to stop tape playback. I Pause button I Press to pause tape playback. HARDWARE OPTIONS MENU SELECTION POWER AUTO OFF DESCRIPTION AND OPERATION I I I Select to choose POWER AUTO OFF or POWER LAST STATE. POWER AUTO OFF - When the key is turned on the system power will remain off, regardless of the system on/off state when the key was turned off. POWER LAST STATE - When the key is turned on the system will automatically return to the power on/off state it was in when the key was turned off. FM MODULATOR - allows the universal remote to turn 9 FM MODULATOR I I © 2001 Directed Electronics, Inc. I I the FM modulator on/off. CATV IRC - for non-cable ready TV's. ANTENNA TV I I I CATV STD I I I I Installation INSTALLATION PRECAUTIONS 1. This product is designed for installation into vehicles with standard (-) 12 volt ground electrical systems. All components should be installed in a manner that will not interfere with the normal operation of the vehicle. Route all wires and cables so they cannot be pinched, punctured, or chaffed by sharp metal or screws during reassembly or vehicle operation. Disconnect the battery's negative terminal or remove any fuses from circuits that are affected before the installation. [. . . ] Each connector provides input/outputs for video, stereo audio, and Infrared remote operation. For a guide to the capabilities of the MCB 1000 refer to the System TV antenna connector - This is a standard F-type TV antenna connector. It can be connected to with Directed Video's TVA 10 telescoping antenna for broadcast TV or a standard cable TV connection. Audio level controls - These are adjustable source audio input level controls. [. . . ]