User manual DAXTEN VOYAGER MICRO BROCHURE

[. . . ] Revision 1. 1 Voyager Micro Introduction Thank you for purchasing the Voyager Micro. This product will allow you to place your Monitor and PS/2 Keyboard and PS/2 Mouse up to 70 meters away from your computer or KVM switch. All models of the Voyager Micro require that that the keyboard and mouse that you will use be PS/2 type. The USB model supports Windows 98 and later, SUN, SGI, MAC and other operating systems that support a USB interface. Features Allows you to control a PC from up to 70 meters away, using a single CAT 5, 6 or 7 cable. [. . . ] Connect the Voyager Micro Transmitter unit to your computer's Keyboard Monitor and Mouse ports (If using the USB transmitter then plug the USB plug into your computers USB port). Plug in your Keyboard, Monitor and Mouse into the corresponding Keyboard, Monitor and Mouse ports on the Voyager Micro's Receiver unit. Connect your UTP cable to the Voyager Micro's Transmitter and Receiver units. Adjust the picture tuner on the Voyager Micro Receiver unit if required. Note: Although we would recommend connecting the Voyager Micro to a computer that is turned off, you can connect it to a computer while it is turned on. Place cables away from fluorescent lights, air conditioners, and machines that are likely to generate electrical noise 3. 8. LED indicators The Voyager Micro Transmitter and Receiver units both have 2 LEDs above the RJ45 port. The flashing yellow LED indicates the system is connected. Upgrading the firmware The update software and the latest firmware are available from our website www. daxten. com, in the product support section. There you will also find instructions on how to perform the upgrade. Configuration options Configure the Voyager Micro to: Work with Unix servers Input the monitor's DDC information Change the hotkey from Shift to Ctrl Enter the Voyager Micro configuration mode by pressing Shift Tab ­ as set out below - all 3 LEDs illuminate. Pressing Esc exits the configuration mode and the LEDs return to normal. Note: Press the keys one after the other not all together. Working with Unix servers Configure the system to work with Unix servers UNIX Version HP UX, SGI and Open VMS Alpha Unix AIX Hotkey Shift Shift Shift Key 1 Tab Tab Tab Key 2 U U U Key 3 1 2 3 Key 5 Esc Esc Esc DDC (Display Data Channel) Information DDC is a VESA standard for communication between a monitor and a video adapter To enter the monitor's DDC information into the Transmitter's memory, press: Shift Tab D Esc Ensure that you update the information when you change the monitor. This is done by simply repeating the hotkey sequence shown above. Changing the Shift hotkey to Ctrl You can change the hotkey to Ctrl Once you do so, replace all the instances of Shift appearing above to Ctrl . To change the hotkey to Ctrl press: Shift Tab C Esc To change the hotkey back to Shift press: Ctrl Tab S Esc Quick Setup Guide Service Information Technical Support If you cannot determine the nature of a problem, please call Daxten and ask for Technical Support. If possible, call from a phone located near the unit, as we may be able to solve your problem directly over the phone. If we cannot solve your problem, and determine that the fault is in the unit, we will issue a Return Material Authorisation (RMA) number that must appear on the outside of all returned products. The unit should be double-packed in the original container, insured, and shipped to the address given to you by our Technical Support representative. The Technical Support offices are found on the back of this manual. Limited Warranty Daxten warrants to the end user that this product is and will be free from defects in materials and workmanship for a period of 24 months from the date of purchase. If during the warranty period the product should fail, the purchaser must promptly call Daxten for a RETURN MATERIALS AUTHORIZATION (RMA) number. [. . . ] It should be deposited at an appropriate facility to enable recovery and recycling. For information on how to recycle this product, please check with the reseller of the product that replaces this product "Take Back" or the original seller of this product. www. daxten. com Ireland Bay 21 Free Zone West Shannon, Co. Clare info. ie@daxten. com www. daxten. ie Tel: +353 (0) 61 23 4000 Fax: +353 (0) 61 23 4099 USA 811 W. Evergreen Ave Suite 302A Chicago, IL 60622 info. us@daxten. com www. daxten. us Tel: +1 312 475 0795 Fax: +1 312 475 0797 United Kingdom 5 Manhattan Business Park Westgate London W5 1UP info. uk@daxten. com www. daxten. co. uk Tel: +44 (0) 20 8991 6200 Fax: +44 (0) 20 8991 6299 · Österreich Künstlergasse 11/4 A-1150 Wien info. at@daxten. com www. daxten. at Tel: +43 (0)1 879 77 65 Fax: +43 (0)1 879 77 65 30 · Deutschland Salzufer 16, Geb. [. . . ]