User manual D-LINK DSL-2750B

[. . . ] 112 D-Link DSL-2750B User Manual 2 Section 1 - Product Overview Package Contents • • • • • • • DSL-2750B Wireless ADSL Router 2 non-detachable Antennas(MIMO 2x2) Power Adapter CD-ROM with Installation Wizard, User Manual, and Special Offers One twisted-pair telephone cable used for ADSL connection One straight-through Ethernet cable One Quick Installation Guide Note: Using a power supply with a different voltage rating than the one included With the DSL-2750B will cause damage and void the warranty for this product. 11n technology for high-speed wireless connection, complete compatibility with 802. 11b/g wireless devices TOTAL SECURITY Firewall protection from Internet attacks , user access control , WPA/WPA2 wireless security. ULTIMATE INTERNET CONNECTION The DSL-2750B ADSL2+ router is a versatile, high-performance remote router for home and the small office. [. . . ] SLAAC+RDNSS to set computers on Router network obtained IPv6 address by RDNSS Stateful DHCP to set computers on Router network obtained IPv6 address by Stateful DHCP, you need type the IPv6 Address Range (Start and End) D-Link DSL-2750B User Manual 44 Section 3 - Configuration Connection type: Autoconfiguration (SLAAC/DHCPv6) IPv6 DNS SETTING Choose Obtain IPv6 DNS servers automatically or type Primary IPv6 DNS server and Secondary IPv6 DNS server. lAN IPv6 ADDRESS SETTINGS Enable DHCP-PD to used Prefix Delegation assigned IPv6 Prefix. aDDRESS AUTOCONFIGURATION SETTINGS SLAAC+Stateless DHCP to set computers on Router network obtained IPv6 address by stateless DHCP. SLAAC+RDNSS to set computers on Router network obtained IPv6 address by RDNSS Stateful DHCP to set computers on Router network obtained IPv6 address by Stateful DHCP, you need type the IPv6 Address Range (Start and End) D-Link DSL-2750B User Manual 45 Section 3 - Configuration Connection type: PPPoE PPPoE session set Share with IPv4 At Address Mode if you choose Dynamic IP, router will obtained WAN IPv6 address by Dynamically or you can set static IPv6 address in Static IP Address/Prefix Length to router. Type User Name, Password, Verify Password, Service Name(if necessarily), Reconnect Mode set to Always on, set MTU value which you want but should be less than 1492 on the MTU These information provided by your Internet Service Provider (ISP) IPv6 DNS SETTING Choose Obtain IPv6 DNS servers automatically or type Primary IPv6 DNS server and Secondary IPv6 DNS server. lAN IPv6 ADDRESS SETTINGS Enable DHCP-PD to use Prefix Delegation assigned IPv6 Prefix. aDDRESS AUTOCONFIGURATION SETTINGS SLAAC+Stateless DHCP to set computers on Router network obtained IPv6 address by stateless DHCP. D-Link DSL-2750B User Manual 46 Section 3 - Configuration SLAAC+RDNSS to set computers on Router network obtained IPv6 address by RDNSS Stateful DHCP to set computers on Router network obtained IPv6 address by Stateful DHCP, you need type the IPv6 Address Range (Start and End) Connection type: DS-Lite Choose DS-Lite DHCPv6 Option, If you choose Manual Configuration, need type the AFTR IPv6 Address. type B4 IPv4 Address (if necessarily) Type WAN IPv6 Address and IPv6 WAN Default Gateway. D-Link DSL-2750B User Manual 47 Section 3 - Configuration USB SETUP To configure the USB Device on the router, click USB Setup in the SETUP tab. Router can configure as a USB device server when you plug-in a USB Storage device. Router can configure as a USB Printer server when you plug- in a USB Printer device. Router can connect to Internet via 3G when you plug-in a 3G USB Modem. To access the USB SETUP setting window, click on the USB SETUP button in the SETUP tab Print Server: allows you to share your USB printer to all the connected local hosts. Last, configure your local hosts (Add Printer Wizard) to utilize this printer. To configure USB port to Print Server setting, choose Enable SharePort and Print Server in the USB Setup page and press Apply button, And you also can share the USB printer or USB storage device to all connect local hosts by SharePort Utility. SharePort Utility manual shows in Appendix–G D-Link SharePort™ To setup Printer Server, press setup button in USB SETUP window enter the server configuration page D-Link DSL-2750B User Manual 48 Section 3 - Configuration Hook the Enable on-board print server to enable the on-board printer server Type the Printer name of the printer which must be exactly the same as configured in the local hosts while setting up a network printer. Type an number from 1 to 128 in Make an Model Press Apply button to apply configuration. D-Link DSL-2750B User Manual 49 Section 3 - Configuration USB Storage Server allows you to share your USB storage device to all the connected local hosts. To configure USB port to USB Storage server setting, choose Enable USB Storage Server in the USB Setup page and press Apply button, To setup USB Storage Server, press Setup button in STORAGE SETUP window enter the server configuration page USB DEVICE STATUS can check the USB Device Status and press Status Refresh button to refresh the status. D-Link DSL-2750B User Manual 50 Section 3 - Configuration You can check Add, Edit and Delete the user in the SAMBA FILE SERVER USER PROFILE. You can check Add, Edit and Delete the user in the FTP SERVER USER PROFILE. [. . . ] CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. D-Link DSL-2750B User Manual 104 Appendix E – Contacting Technical Support Contacting Technical Support You can find software updates and user documentation on the D-Link websites. If you require product support, we encourage you to browse our FAQ section on the Web Site before contacting the Support line. [. . . ]