User manual D-LINK DI-300

[. . . ] Copyright Statement Copyright ©1997 D-Link Corporation No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc. , as stipulated by the United States Copyright Act of 1976. Trademarks D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective owners. Limited Warranty This guide and the accompanying product are each provided "as is, " without warranty as to their performance, merchantability or fitness for any particular purpose. reserve the right to revise this publication and to make changes to its contents at any time, without obligation to notify any person or entity of such revisions or changes. Table of Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Additionally, you will have to create a Remote Node for the router on the remote network (see the Remote Node Configuration chapter starting on page 48). An example of a DI-300 or DI-300M being used as a dial-in server is shown below: Default Dial-In Setup This section covers the default dial-in parameters. The parameters in Menu 13 affect incoming calls from all Remote Dial-in Users and Remote Nodes before authentication is completed. Once authentication is completed, and if it matches a Remote Node, the router will use parameters from that particular Remote Node. Dial-In Configuration 61 From the Main Menu, enter 13 to go to Menu 13 - Default Dial-in Setup. This section will describe how to configure the protocolindependent fields in this menu. Telco Options: CLID Authen. --This field sets the CLID authentication parameter for all incoming calls. Preferred--If the CLID is available then CLID will be used to do authentication. Authen. --This field sets the authentication protocol used for incoming calls. User names and passwords are configured in the next section (Remote users/Dial-in Users Setup). Options for this field are: 62 Dial-In Configuration CHAP/PAP--The router will try CHAP first, but PAP will be used if CHAP is not available. PPP Options: Compression--The setting in this field determines if Stac compression will be used. That is, the node that initiates the call will request a user name and password from the far end that they are dialing to. If the Remote Node that is dialing in implements this type of authentication, set this field to Yes. Enter in the login name to be used to respond to the far end's PAP authentication request. Enter in the PAP password to be used to respond to the far end's authentication request. Multiple Link Options: Max Trans Rate--Enter the maximum data transfer rate between your router and the Remote Dial-in User. There are two options for this field: 64--At most, one B channel will be used. 128--A maximum of two channels can be used. Dial-In Configuration 63 When the DI-300 or DI-300M calls back to the Remote Dial-in User the maximum data transfer rate is always 64. Callback Budget Management: Allocated Budget (min)-- This field will set a budget callback time for all the Remote Dial-in Users. Callback Budget Management: Period (hr)--This field will set the time interval to reset the above callback budget control. 10. Dial-In IP Address Supplied By: Dial-in User--If set to Yes, it tells the DI-300 or DI-300M to allow a remote host to specify its own IP address. This is to prevent the remote host from using an invalid IP address and potentially disrupting the whole network. [. . . ] The Simple Network Management Protocol; an industry-standard protocol for remotely monitoring and controlling network devices from a Network Management System (NMS). SNMP requests are usually transmitted using TCP/IP, though other means are possible. Glossary Segment SLIP SNMP 154 Store-andForward STP Message passing system where the entire message is received before being passed on to the next node. Spanning Tree Protocol; a network protocol defined in IEEE standard 802. 1d, ensuring that a collection of bridges can forward packets throughout the entire interconnected network, while preventing endless network loops. Transmission Control Protocol/Internet Protocol; a suite of transport and network layer communications protocols. [. . . ]