User manual D-LINK DGS-3212SR

[. . . ] Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben. Sorgen Sie dafür, daß diese Öffnungen nicht 7. 8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. [. . . ] The switch and the server must be configured exactly the same, using the same protocol. (For example, if the Switch is set up for TACACS authentication, so must be the host server. ) The Access Authentication Control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command enable authen_policy disable authen_policy show authen_policy create authen_login method_list_name config authen_login Parameters <string 15> [default | method_list_name <string 15>] method {tacacs | xtacacs | tacacs+ | radius | server_group <string 15> | local | none} <string 15> {default | method_list_name <string 15> | all} <string 15> [default | method_list_name <string 15>] method {tacacs | xtacacs | tacacs+ | radius | server_group <string 15> | local_enable | none} <string 15> [default | method_list_name <string 15> | all] {console | telnet | ssh | http | all] [login | enable] [default | method_list_name <string 15>] delete authen_login method_list_name show authen_login create authen_enable method_list_name config authen_enable delete authen_enable method_list_name show authen_enable config authen application show authen application create authen server_group config authen server_group <string 15> [tacacs | xtacacs | tacacs+ | radius | <string 15>] [add | delete] server_host <ipaddr> protocol [tacacs | xtacacs | tacacs+ | radius] <string 15> {<string 15>} <ipaddr> protocol [tacacs | xtacacs | tacacs+ | radius] {port <int 1-65535> | key [<key_string 254> | none] | timeout <int 1255> | retransmit <int 1-255>} <ipaddr> protocol [tacacs | xtacacs | tacacs+ | radius] {port <int 1-65535> | key [<key_string 254> | none] | timeout <int 1255> | retransmit <int 1-255>} <ipaddr> protocol [tacacs | xtacacs | tacacs+ | radius] 161 delete authen server_group show authen server_group create authen server_host config authen server_host delete authen server_host xStack Gigabit Layer 3 Switch Command Line Interface Manual Command show authen server_host config authen parameter response_timeout config authen parameter attempt show authen parameter enable admin config admin local_enable Parameters <int 1-255> <int 1-255> <password 15> Each command is listed, in detail, in the following sections. enable authen_policy Purpose Syntax Description Used to enable system access authentication policy. enable authen_policy This command will enable an administrator-defined authentication policy for users trying to access the Switch. When enabled, the device will check the method list and choose a technique for user authentication upon login. Only administrator-level users can issue this command. Parameters Restrictions Example usage: To enable the system access authentication policy: DGS-3324SRi:4#enable authen_policy Command: enable authen_policy Success. DGS-3324SRi:4# disable authen_policy Purpose Syntax Description Used to disable system access authentication policy. disable authen_policy This command will disable the administrator-defined authentication policy for users trying to access the Switch. When disabled, the Switch will access the local user account database for username and password verification. In addition, the Switch will now accept the local enable password as the authentication for normal users attempting to access administrator level privileges. Only administrator-level users can issue this command. Parameters Restrictions 162 xStack Gigabit Layer 3 Switch Command Line Interface Manual Example usage: To disable the system access authentication policy: DGS-3324SRi:4#disable authen_policy Command: disable authen_policy Success. DGS-3324SRi:4# show authen_policy Purpose Syntax Description Parameters Restrictions Example usage: To display the system access authentication policy: DGS-3324SRi:4#show authen_policy Command: show authen_policy Authentication Policy: Enabled DGS-3324SRi:4# Used to display the system access authentication policy status on the Switch. local - Adding this parameter will require the user to be authenticated using the local user account database on the Switch. none ­ Adding this parameter will require no authentication to access the Switch. method_list_name ­ Enter a previously implemented method list name defined by the user. The user may add one, or a combination of up to four (4) of the following authentication methods to this method list: tacacs ­ Adding this parameter will require the user to be authenticated using the TACACS protocol from a remote TACACS server. xtacacs ­ Adding this parameter will require the user to be authenticated using the XTACACS protocol from a remote XTACACS server. tacacs+ ­ Adding this parameter will require the user to be authenticated using the TACACS protocol from a remote TACACS server. radius - Adding this parameter will require the user to be authenticated using the RADIUS protocol from a previously configured RADIUS server. server_group <string 15> - Adding this parameter will require the user to be authenticated using a user-defined server group previously configured on the Switch. local - Adding this parameter will require the user to be authenticated using the local user account database on the Switch. none ­ Adding this parameter will require no authentication to access the Switch. NOTE: Entering none or local as an authentication protocol will override any other authentication that follows it on a method list or on the default method list. Restrictions Example usage: Only administrator-level users can issue this command. To configure the user defined method list "Trinity" with authentication methods TACACS, XTACACS and local, in that order. DGS-3324SRi:4#config authen_login method_list_name Trinity method tacacs xtacacs local Command: config authen_login method_list_name Trinity method tacacs xtacacs local Success. [. . . ] ren <source_path_filename 64> <target_path_filename 64> This command is used to rename a filename located on the storage media accessory. <source_path_filename 64> - Enter the path and name of the file to be renamed. <target_path_filename 64> - Enter the new name and path of the file 341 xStack Gigabit Layer 3 Switch Command Line Interface Manual ren to be renamed. Restrictions Example usage: To rename a file: DGS-3324SRi:4#ren c:/abc. txt c:/cba. txt Command: ren c:/abc. txt c:/cba. txt Done!! [. . . ]