User manual D-LINK DGS-108

[. . . ] D-LinkTM DGS-108 8-Port 10/100/1000Mbps Gigabit Ethernet Switch Manual First Edition Building Networks for People RECYCLABLE D-Link DGS-108 Unmanaged Gigabit Ethernet Switch ____________________ Information in this document is subject to change without notice. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. [. . . ] After the Switch is powered on, the LED indicators will momentarily blink. This blinking of the LED indicators represents a reset of the system. Power Failure As a precaution, in the event of a power failure, unplug the Switch. When power is resumed, plug the Switch back in. 8 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Section 3 Connecting The Switch Switch To End Node Switch To Hub or Switch Connecting To a Server NOTE: All eight high-performance NWay Ethernet ports can support both MDIII and MDI-X connections. Switch To End Node End nodes include PCs outfitted with a 10, 100, or 1000 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. The end node can be connected to any of the ports of the Switch. Figure 3-1. Switch connected to an end node The Link/Act LEDs for each UTP port light green when the link is valid. The LED over the port label indicates a port speed of either 10/100 Mbps or 1000Mbps. A blinking LED on the bottom indicates packet activity on that port. Switch to Hub or Switch These connections can be accomplished in a number of ways using a standard Ethernet cable. · A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. · A 100BASE-T hub or switch can be connected to the Switch via a twisted -pair Category 5 UTP/STP cable. 9 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch · A 1000BASE-T switch can be connected to the Switch via a twisted -pair Category 5e or better UTP/STP cable. Figure 3-2. Switch connected to a port on a hub or switch using either a straight or crossover cable­ any standard Ethernet cable is fine Connecting To Network Backbone or Server Any of the eight Gigabit Ethernet ports are ideal for uplinking to a network backbone or network server. Figure 3-3. Connection to a Server 10 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Appendix A Technical Specifications General Standards: IEEE 802. 3ab 1000BASE-T IEEE 802. 3u 100BASE-TX IEEE 802. 3 10BASE-T IEEE 802. 3x Flow Control IEEE 802. 1p QOS CSMA/CD Ethernet: 10Mbps 20Mbps Fast Ethernet: 100Mbps 200Mbps Gigabit Ethernet: Topology: Network Cables: Star Ethernet: Fast Ethernet: Gigabit Ethernet: Number of Ports: 2-pair UTP Cat. 5, Unshield Twisted Pair (UTP )Cable 2000Mbps (Half-duplex) (Full-duplex) (Half-duplex) (Full-duplex) (Full-duplex) Protocol: Data Transfer Rate: Eight 10/100/1000BASE-T Gigabit Ethernet ports Physical and Environmental AC-DC 7. 5V/1. 5A This unit is to be used with a power supply listed below or equivalent: AM-0751000D41 for USA DC Inputs: AM-0751000S41 for Australia AM-0751000B for UK AM-0751000M for China AM-0751000V for Europe Power Consumption: Operating Temperature: Storage Temperature: Humidity: Dimensions: EMI Safety: 6. 7 watts maximum 32°F ~ 104F ° (0 °C ~ 40) 14°F ~ 158°F (-10°C ~ 70°C) 5% ~ 95% RH, non-condensing 7. 76 in. (197 mm x 114 mm x 8. 6 mm) FCC Class B, CE Mark Class B CSA International 11 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Performance Transmission Method: RAM Buffer: Filtering Address Table: Packet Filtering/ Forwarding Rate: MAC Address Learning: Jumbo Frame: Store-and-forward 144K per device 8K MAC address per device Full wire speed Self-learning, auto-aging 9. 6 KB 12 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Glossary 1000BASE-LX ­ A long wavelength for a "long haul" fiber optic cable for a maximum length of 10 kilometers. 1000BASE-SX ­ A short laser wavelength on multimode fiber optic cable for a maximum length of 550 meters. 100BASE-TX ­ 100Mbps Ethernet implementation over Category 5 and Type 1 Twisted Pair cabling. 10BASE-T ­ The IEEE 802. 3 specification for Ethernet over Unshielded Twisted Pair (UTP) cabling. aging ­ The automatic removal of dynamic entries from the Switch Database which have timed-out and are no longer valid. A connection oriented transmission protocol based on fixed length cells (packets). ATM is designed to carry a complete range of user traffic, including voice, data, and video signals. auto-negotiation ­ A feature on a port, which allows it to advertise its capabilities for speed, duplex, and flow control. When connected to an end station that also supports auto-negotiation, the link can self-detect its optimum operating setup. [. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office. Registration Information Register online your D-Link product at http://support. dlink. com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. International Offices U. S. A 17595 Mt. 92708 TEL: 714-885-6000 Fax 866-743-4905 URL: www. dlink. com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www. dlink. ca Europe (U. K. ) 4th Floor, Merit House Edgware Road, Colindale London NW9 5AB U. K. [. . . ]