User manual D-LINK DGS-1008MP

[. . . ] D-Link™ DGS-108 8-Port 10/100/1000Mbps Gigabit Ethernet Switch Manual First Edition Building Networks for People RECYCLABLE D-Link DGS-108 Unmanaged Gigabit Ethernet Switch ____________________ Information in this document is subject to change without notice. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. [. . . ] Make sure that there is adequate space for proper heat dissipation from and adequate ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front and rear of the Switch for ventilation. Install the Switch in a fairly cool and dry place for the acceptable temperature and humidity operating ranges. Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight. When installing the Switch on a level surface, attach the rubber feet to the bottom of the device. The rubber feet cushion the Switch, protect the casing from scratches, and prevent it from scratching other surfaces. 6 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Mounting the Switch on a Wall The DGS-108 can be mounted on a wall. Two mounting slots are provided on the bottom of the Switch for this purpose. Mounting the Switch to a Wall 7 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Attaching the Rubber Feet Use the rubber feet provided. Position and apply the rubber feet to the underside of the DGS-108 Switch. Figure 2- 2. Attaching the Rubber Feet Provide for Adequate Ventilation CAUTION: Do not place any device on top of Switch, or place the Switch on top of any device or object that will block the free flow of air through the ventilation slots on the sides, top, and bottom of the Switch’s case. In addition, care should be taken not to locate the Switch next to, on top of, or underneath any device that generates a significant amount of heat. For the Switch to perform at its optimal level, the Switch must have adequate ventilation to prevent the Switch from overheating and becoming damaged. Power On Plug one end of the AC to DC power converter into the power connector of the Switch and the other end into the local power source outlet. After the Switch is powered on, the LED indicators will momentarily blink. This blinking of the LED indicators represents a reset of the system. Power Failure As a precaution, in the event of a power failure, unplug the Switch. When power is resumed, plug the Switch back in. 8 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch Section 3 Connecting The Switch Switch To End Node Switch To Hub or Switch Connecting To a Server NOTE: All eight high-performance NWay Ethernet ports can support both MDIII and MDI-X connections. Switch To End Node End nodes include PCs outfitted with a 10, 100, or 1000 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable. The end node can be connected to any of the ports of the Switch. Figure 3-1. Switch connected to an end node The Link/Act LEDs for each UTP port light green when the link is valid. The LED over the port label indicates a port speed of either 10/100 Mbps or 1000Mbps. A blinking LED on the bottom indicates packet activity on that port. Switch to Hub or Switch These connections can be accomplished in a number of ways using a standard Ethernet cable.  A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e UTP/STP cable.  A 100BASE-T hub or switch can be connected to the Switch via a twisted -pair Category 5 UTP/STP cable. 9 D-Link DGS-108 Unmanaged Gigabit Ethernet Switch  A 1000BASE-T switch can be connected to the Switch via a twisted -pair Category 5e or better UTP/STP cable. Figure 3-2. [. . . ] Consult the dealer or an experienced radio/TV technician for help. For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link office. Registration Information Register online your D-Link product at http://support. dlink. com/register/ Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. International Offices U. S. A 17595 Mt. 92708 TEL: 714-885-6000 Fax 866-743-4905 URL: www. dlink. com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www. dlink. ca Europe (U. K. ) 4th Floor, Merit House Edgware Road, Colindale London NW9 5AB U. K. TEL: 44-20-8731-5555 FAX: 44-20-8731-5511 URL: www. dlink. co. uk Germany Schwalbacher Strasse 74 D-65760 Eschborn Germany TEL: 49-6196-77990 FAX: 49-6196-7799300 URL: www. dlink. de France Le Florilege #. 2, Allee de la Fresnerie 78330 Fontenay le Fleury France TEL: 33-1-30238688 FAX: 33-1-30238689 URL: www. dlink-france. fr Netherlands Weena 290 3012 NJ Rotterdam Netherlands Tel: +31-10-282-1445 Fax: +31-10-282-1331 URL: www. dlink-benelux. com Belgium Rue des Colonies 11 B-1000 Brussels Belgium Tel: +32(0)2 517 7111 Fax: +32(0)2 517 6500 URL: www. dlink-benelux. com Italy Via Nino Bonnet n. [. . . ]