User manual D-LINK DES-6000

[. . . ] DES-6000 Modular Ethernet Switch User's Guide Second Edition (April 2001) 6DES6000. . 02 Printed In Taiwan RECYCLABLE TABLE OF CONTENTS ABOUT THIS GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V CONVENTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V OVERVIEW OF THIS USER'S GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model numbers are normally used only to differentiate between specific Switches where necessary. Unless differentiated by model number, all information applies to both models. Overview of this User's Guide Chapter 1, "Introduction. " Describes the Switch and its features. [. . . ] MAC Address The MAC address of the broadcast domain member being added or removed. Please note that the Status field for the MAC address you have entered may read Inactive. Once the Switch is restarted in MAC-based broadcast domain mode, the MAC-addresses will be applied, meaning that the broadcast domains and their entries are active. Current Broadcast Domains, Number of Members, MAC Address (in the lower part of the screen), and Status reflect the current conditions. They are read-only fields and cannot be changed. Configure 802. 1Q VLAN If you are unsure of your knowledge of 802. 1Q VLANs or IEEE 802. 1Q tagging, we highly recommend reviewing the VLANs & MAC_based Broadcast Domains section of the "Switch Management Concepts" chapter in this manual before proceeding. Using the Console Interface 57 Modular Ethernet Switch User's Guide To configure an IEEE 802. 1Q VLANs, you must do three things: 1. Decide if you want to enable Ingress Filtering and enable it on the chosen ports. Ingress filtering applied on a port causes the port to examine all incoming packets and check whether the port itself is a member of the VLAN on which the packet is destined. This is normally used to keep untagged frames off the switch, although it can have other uses as well. This setting is configurable for each port in the Configure Port Ingress Filtering Check screen. A port can transmit packets (coming from the connected segment) onto only one VLAN. It can receive packets (transmit packets to the connected segment) on many VLANs. Active VLAN designations are defined by assigning Port VLAN ID numbers (PVIDs) in the Configure Default Port VLAN ID screen. Define the VLAN itself and assign the ports that will be passive members (able to receive packets with this VID tag or from a port that has this PVID number). At this point, you need to designate whether a member port will be a Tagging or Untagging member port. Defining the ports that will be members of a VLAN, and whether they will Tag or Untag packets is done in the Configure 802. 1Q Static VLAN Entry screen. Choose Configure 802. 1Q VLANs on the VLAN Configuration screen (under Configure VLAN of the System Configuration menu) to access the 802. 1Q VLAN Configuration menu: Figure 6-36. 802. 1Q VLAN Configuration menu Choose Configure Port Ingress Filter to access the first item on the menu. Ingress Filter screen 58 Using the Console Interface Modular Ethernet Switch User's Guide This screen allows you to Enable or Disable Ingress filtering for each port. When a packet arrives at the port from the connected segment and Ingress filtering is Enabled, the port will check the VLAN ID number of the packet, and its own VID. If the packet doesn't have a VLAN tag or the port is not a member of the VLAN (doesn't have the same VID) as the packet, the packet will be discarded. Note: If a port is a member of a trunk group but is not the anchor, the items shown in the above table will be read-only and the values will be the same as those for the anchor port. Choose Configure Port VLAN ID (PVID) to access the second item on the 802. 1Q VLAN Configuration menu. Port VLAN (PVID) Assignment screen This screen allows you to set a Port VLAN ID number (PVID) for each port. [. . . ] Expedited shipping is available upon request and provided shipping charges are prepaid by the customer. · · · D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link's reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming. What Is Not Covered: The Limited Warranty provided herein by D-Link does not cover: Products that, in D-Link's judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product. While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service Office. [. . . ]