User manual D-LINK DES-3010GA Reference Guide

[. . . ] D-Link DES-3010FA/GA/PA CLI Reference Guide Table of Contents Section 1. Using the CLI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. 1 CLI Command Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1. 1. 1 1. 1. 2 1. 1. 3 1. 1. 4 1. 1. 5 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To disable the command history function, use the no form of this command. Syntax terminal history no terminal history Default Configuration The default configuration for all terminal sessions is defined by the history line configuration command. Command Mode User or Priviliged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example disables the command history function for the current terminal session. Console> no terminal history Page 140 D-Link DES-3010FA/GA/PA CLI Reference Guide terminal history size The terminal history size User or Priviliged EXEC command configures the command history buffer size for the current terminal session. To reset the command history buffer size to the default setting, use the no form of this command. . Syntax terminal history size number-of-commands no terminal history size Parameters · number-of-commands--Specifies the number of commands the system may record in its command history buffer. (Range: 10-200) Default Configuration The default command history buffer size is 10. Command Mode User or Priviliged EXEC mode User Guidelines The terminal history size user EXEC command configures the size of the command history buffer for the current terminal session. To change the default size of the command history buffer, use the history line configuration command. The maximum number of commands in all buffers is 256. Examples The following example configures the command history buffer size to 20 commands for the current terminal session. Console> terminal history size 20 Page 141 Line Commands show line The show line User or Priviliged EXEC mode command displays line parameters. Syntax show line [console | telnet | ssh] Parameters console -- Console terminal line. · · telnet -- Virtual terminal for remote console access (Telnet). · ssh -- Virtual terminal for secured remote console access (SSH). Default Configuration If the line is not specified, the default value is console. Command Mode User or Priviliged EXEC mode User Guidelines There are no user guidelines for this command. Examples The following example displays the line configuration. Console> show line Console configuration: Interactive timeout: Disabled History: 10 Baudrate: 9600 Databits: 8 Parity: none Stopbits: 1 Telnet configuration: Interactive timeout: 10 minutes 10 seconds History: 10 SSH configuration: Interactive timeout: 10 minutes 10 seconds History: 10 Page 142 D-Link DES-3010FA/GA/PA CLI Reference Guide Section 12. Management ACL management access-list The management access-list Global Configuration mode command configures a management access list and enters the Management Access-list Configuration command mode. To delete an access list, use the no form of this command. Syntax management access-list name no management access-list name Parameters · name -- Access list name. (Range: 1-32 characters) Default Configuration This command has no default configuration. Command Mode Global Configuration mode User Guidelines Use this command to configure a management access list. The command enters the Access-list Configuration mode, where permit and deny access rules are defined using the permit (Management) and deny (Management) commands. If you reenter an access list context, the new rules are entered at the end of the access list. Use the management access-class command to select the active access list. Management ACL requires a valid management interface, which is a port, VLAN, or port-channnel with an IP address or console interface. Management ACL only restricts access to the device for management configuration or viewing. Examples The following example creates a management access list called mlist, configures management Ethernet interfaces 1 and 6 and makes the new access list the active list. Console(config)# management access-list mlist Console(config-macl)# permit ethernet 1 Console(config-macl)# permit ethernet 6 Console(config-macl)# exit Console(config)# management access-class mlist Page 143 Management ACL The following example creates a management access list called mlist, configures all interfaces to be management interfaces except Ethernet interfaces 1 and 6 and makes the new access list the active list. Console(config)# management access-list mlist Console(config-macl)# deny ethernet 1 Console(config-macl)# deny ethernet 6 Console(config-macl)# permit Console(config-macl)# exit Console(config)# management access-class mlist Page 144 D-Link DES-3010FA/GA/PA CLI Reference Guide permit (Management) The permit Management Access-List Configuration mode command defines a permit rule. Syntax permit [ethernet interface-number | vlan vlan-id | port-channel port-channel-number | service] permit ip-source ip-address [mask mask | prefix-length] [ethernet interface-number | vlan vlan-id | port-channel port-channel-number | service] Parameters interface-number -- A valid Ethernet port number. · prefix-length -- Number of bits that comprise the source IP address prefix. [. . . ] Wrong network address in the workstation No network address set Wrong or missing protocol Faulty ethernet cable Faulty port Faulty module Incorrect initial configuration No connection is established and the port LED is on Device is in a reboot loop Software fault Page 356 D-Link DES-3010FA/GA/PA CLI Reference Guide P r o bl e m s No connection and the port LED is off P os s i bl e C a u s e Incorrect ethernet cable, e. g. , crossed rather than straight cable, or vice versa, split pair (incorrect twisting of pairs) Fiber optical cable connection is reversed Bad cable Wrong cable type Sol ut i on Check pinout and replace if necessary Change if necessary. Check Rx and Tx on fiber optic cable Replace with a tested cable Verify that all 10 Mbps connections use a Cat 5 cable Check the port LED or zoom screen in the NMS application, and change setting if necessary Page 357 P r o bl e m s Add and Edit pages do not open. Lost password P os s i bl e C a u s e A pop-up blocker is enabled. Sol ut i o n Disable pop-up blockers. The Password Recovery Procedure enables the user to set the password back to the default setting. [. . . ]