User manual CATERPILLAR D8T WH BROCHURE

[. . . ] The heavy-duty hinged radiator guard protects the cooling system. Crankcase (belly) Guards. They help prevent contact damage to vital power train components, and help keep debris out of the power train compartments. Note: The D8T features an attachment guard that can be electrically raised and lowered. Pivot Shaft Seal Guards. The pivot shaft seal guards help prevent debris from entering and damaging the Duo-Cone® seals as well as protecting the bolts on the pivot shaft seal retainers. Tilt Cylinder Lines Guards. [. . . ] Debris stratifies along the outer wall and is ejected back into the environment. Remaining contaminates are collected and removed by a secondary scavenger system, allowing only precleaned air to continue to the engine's air filter. 7 Required Attachments These options must be ordered in addition to the basic Waste Handling Arrangement. Enhanced Cab. The enhanced cab provides higher cab pressurization for improved cab air quality in dust and debris-laden applications. Includes a powered precleaner, with a high efficiency filter, which reduces system maintenance intervals. Hydraulic and Fuel Tank guard. The hydraulic and fuel guard helps protect implement hydraulic oil tank, battery box and fuel tank. Supplemental Cylinder Mounted Lights. The supplemental cylinder mounted lights (four front) are repositioned from the fender/ openings to the top of the cylinders. The fender openings are covered with plates to prevent debris from entering. Chose from either Halogen or HID (high intensity discharge). Engine Enclosures. The enclosures help prevent airborne materials from entering the engine compartment and help reduce radiator plugging, which can cause cooling system problems. Note: If the sound suppression arrangement is ordered, the perforated side panels are replaced with solid doors and the perforated hood is replaced with larger rectangular perforations. Rear Striker Bars. The rear striker bars incorporate a rigid drawbar and housing with large access doors for storage on machines not equipped with rippers. The rear striker bars are counterweightready in case additional rear weight is needed. Note: The D10T uses rear counterweights instead of a housing with doors. 8 ROPS-mounted Air Conditioner Condenser and Fans. The ROPSmounted air conditioner and fans are relocated from the engine compartment to the ROPS. · Moving the condenser and fans away from the radiator reduces the concentration of debris and plugging. This relocation also increases the cooling capacity of the machine for operation in higher temperatures. Laminated Thermal Shields. The laminated thermal shields cover the exhaust stack inside the compartment, hot-side of the turbocharger, and the exhaust manifold. These shields reduce surface temperatures well below the flash point of most common combustibles encountered. Note: The ROPS-mounted position raises the height of the machine an additional 30. 5 cm (12 in). 9 Recommended Options Features for peak performance. Several additional options are recommended to assist in matching your site requirements. Hydraulic Rippers. Hydraulic rippers are available as single or multi-shank to penetrate tough material fast and rip thoroughly. Caterpillar Landfill Blades. The Caterpillar landfill blades increase the dozing capacity in trash and help prevent material from spilling over the blade and entering the radiator. Wear plates are available and are recommended when working in highly abrasive materials. Fast Fuel System. [. . . ] of Cylinders Bore Stroke Displacement Track Rollers (each side) Width of Standard Track Shoe Length of Track on Ground Ground Contact Area (with Std. Shoe) Track Gauge General Dimensions: Height (Stripped Top)*** Height (top of ROPS) Overall Length: with Blade without Blade Width (over Trunnions)**** Width (w/o Trunnions ­ Std. Shoe)**** Ground Clearance Blade Types and Widths: SU U Blade Capacities with Trash Rack: SU LGP (D8) SU U Fuel Tank Refill Capacity D8T 231 kW 310 HP 38 660 kg 85, 150 lb Cat C15 ACERT 1850 6 137 mm 5. 4 in 172 mm 6. 75 in 15. 2 L 928 in3 8 560 mm 22 in 3. 21 m 10 ft 6. 5 in 3. 58 m2 5544 in2 2. 08 m 6 ft 10 in 2. 67 m 3. 46 m 6. 09 m 4. 64 m 3. 05 m 2. 64 m 618 mm 3. 94 m 4. 26 m 21. 1 m3 19. 9 m3 24. 8 m3 643 L 8 ft 9 in 11 ft 4 in 20 ft 0 in 15 ft 2 in 10 ft 0 in 8 ft 8 in 24. 3 in 12 ft 11 in 14 ft 0 in 27. 6 yd3 26. 1 yd3 32. 4 yd3 170. 0 gal D9T 306 kW 410 HP 49 567 kg 109, 180 lb Cat C18 ACERT 1800 8 145 mm 5. 7 in 183 mm 7. 2 in 18. 1 L 1106 in3 8 610 mm 24 in 3. 47 m 11 ft 5 in 4. 24 m2 6569 in2 2. 25 m 7 ft 5 in 3. 00 m 3. 99 m 6. 63 m 4. 91 m 3. 30 m 2. 86 m 596 mm 4. 31 m 4. 66 m N/A 28. 8 m3 33. 5 m3 889 L 9 ft 10 in 13 ft 1 in 21 ft 10 in 16 ft 1 in 10 ft 10 in 9 ft 5 in 23. 5 in 14 ft 2 in 15 ft 3 in N/A 37. 6 yd3 43. 8 yd3 235 gal D10T 433 kW 580 HP 65 764 kg 144, 986 lb Cat C27 ACERT 1800 12 137. 2 mm 5. 4 in 152. 4 mm 6. 0 in 27 L 1647. 5 in3 8 610 mm 24 in 3. 88 m 12 ft 9 in 4. 7 m2 7326 in2 2. 55 m 8 ft 4 in 3. 22 m 4. 34 m 7. 50 m 5. 33 m 3. 72 m 3. 16 m 615 mm N/A 5. 26 m N/A N/A 48. 9 m3 1109 L 10 ft 7 in 14 ft 3 in 24 ft 8 in 17 ft 6 in 12 ft 2 in 10 ft 4 in 24 in N/A 17 ft 3 in N/A N/A 63. 9 yd3 293. 0 gal **** Operating Weight: Includes lubricants, coolant, 100% fuel, hydraulic controls, ROPS canopy, FOPS Cab, SU-Blade (U-Blade for D10T) with trash rack, special radiator core reversible fan, drawbar, engine enclosures, fuel tank guard, extreme service crankcase (belly) guard, heavy-duty hinged radiator guard, higher prescreener, front and rear striker bars and operator. **** Engine model meets current levels of exhaust emission regulations for the EPA, EU, and JMOC at time of manufacture. [. . . ]