User manual BIONAIRE BPH1414
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BIONAIRE BPH1414. We hope that this BIONAIRE BPH1414 user guide will be useful to you.
You may also download the following manuals related to this product:
BIONAIRE BPH1414 MANUAL 2 (874 ko)
Manual abstract: user guide BIONAIRE BPH1414
Detailed instructions for use are in the User's Guide.
[. . . ] If overheating should occur, the built-in overheating safety device will switch off the heater. The heater is to be installed so that switches and other controls cannot be touched by a person in the bath. The heater cannot be used adjacent to curtains or combustible material. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] Turning the unit on/off and setting the Digital Thermostat (BPH1520 Only) 1. Once you have selected the mode and temperature, the display returns to the current room temperature and gradually increases as the room warms. If you selected an Auto mode and the heater does not start, make sure the set temperature is higher than the current room temperature. To turn the unit off keep pressing the mode button (F) until all mode indicator lights (E) are not illuminated. Switch off the on/off switch located on the bottom of the right end cap. With the heater off, press and hold (+) and (-) simultaneously until the display flashes and display the number "0". Press (+) or (-) to select the amount of time you would like to pass before the heater turns on. After setting the timer, the display shows a red dot next to the current room temperature on the display to indicate that the timer is activated. After the programmed length of time has passed, the heater automatically turns on Auto HI at 24°C (75°F) for 2 hours. With the heater running, press and hold (+) and (-) simultaneously until the display flashes. After setting the timer, the display shows a RED dot next to current room temperature on the display to indicate that the timer is activated. PROGRAMMABLE TIMER (BPH1520 Only) You can program your heater to turn on at a preset time or turn off after a set amount of time. To turn the unit off rotate the mode adjustment knob anti-clockwise to the (0) position. FROST GUARD (BPH1414) Keep unit in 1 (low setting) or 2 (high setting) rotate thermostat adjustment knob to beginning position ( ). In this mode, the heater is off until the room's temperature reaches freezing and the heater automatically turns on HI power. This special setting is automatically activated when the (AF) mode is selected. In this mode, the heater is off until the room's temperature reaches freezing and the heater automatically turns on HI power. AUTO SAFETY SHUT OFF The heater has a built in safety device which will switch off the heater automatically in case of accidental overheating. SAFETY BACK-UP FUSE In the unlikely case the heater does not respond to an overheat situation, the safety back-up fuse will engage. TIP OVER PROTECTION When the unit is accidentally knocked over, it will instantly shut off. [. . . ] WARNING  THIS APPLIANCE MUST BE EARTHED The wires in the mains lead are coloured as such: GREEN AND YELLOW EARTH BROWN LIVE BLUE NEUTRAL Please note that the colour of these mains wires may not correspond with the colour markings that identify the terminals in your plug. Please proceed as follows: The wire which is coloured GREEN AND YELLOW must be connected to the terminal which is marked with the letter "E" or by the earth symbol or GREEN AND YELLOW. The BROWN coloured wire must be connected to the terminal, which is marked with the letter "L" or is coloured RED. The BLUE coloured wire must be connected to the terminal, which is marked with the letter "N" or is coloured BLACK. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BIONAIRE BPH1414
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BIONAIRE BPH1414 will begin.