User manual BENQ PALMPRO 7765PA

[. . . ] Digital Multimedia Projector PalmPro 7763PA/65PA User's Guide Thank you very much for purchasing this Benq DLPTM Technology Projector. After reading this manual, keep it for future reference. Outline This DLPTM Technology Projector can display various computer signals and NTSC/PAL/SECAM video signals. Features (1) (2) (3) (4) (5) (6) (7) High brightness High resolution Compact size, light weight for portability RGB input terminal RS232 Communication Mouse emulation Complies with VESA DDC1/2B specifications English I Copyright Copyright © 2002 by Benq Corporation. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. Disclaimer Benq Corporation. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. [. . . ] When the magnify function is active, use disk pad to move through the picture. And the blank screen will be revealed partially from top to bottom by pressing Blank again. The sound gets louder or quieter by pressing the "+" or "-" button. When operating in mouse emulation mode, it registers a left mouse click. When operating in mouse emulation mode, it registers a right mouse click. To move Left/Right among OSD items. Disk Pad Menu Blank Source Mute Volume Laser Mouse Left-Click Mouse Right- Click Exit 34Drag The remote control allows you to operate the function keys on the projector and to emulate mouse function when the projector is connected to a computer. Inserting Batteries in the Remote Control Be sure to follow instructions in placing batteries into the remote control units. · Install two 'AAA' batteries as indicated inside the battery compartment. · Do not mix new and old or different types of batteries. English 11 Figure 15 Battery replacement process Remote Control Range The remote sensors are located on the back of the unit. It can function in a range 50 degrees horizontal and 30 degrees vertical relative to a line that is a right angle to the remote sensor. The distance between the remote control and remote sensor must be shorter than four meters (13 feet). Figure 16 Range Usage and Replacement of Lamp The light source lamp has a limited service life. The picture will become dark or the color will fade after the lamp has been used for a long time. Lamp in excess of service hours When the LED light is a continuous red, it means the lamp has exceeded 1500 service hours. After this light appears, it is advisable to replace the projection lamp as soon as possible. AND RESET THE LAMP TIMER" will be displayed on the screen if the lamp has been operated for 1400 hours (see figure 17). Figure 17 Lamp replacement warning signal English 12 "PLEASE CHANGE A NEW LAMP. THE POWER WILL TURN OFF AFTER 20 HOURS" will be displayed on the screen if the lamp has been operated for 1480 hours. The "20" will count down (see figure 18). Figure 18 Lamp replacement warning signal "PLEASE CHANGE A NEW LAMP" will blink on the screen together with a red LED if the lamp has been operated for more than 1500 hours (see figure 19). All three of the above Figure 19 Lamp replacement warning messages will not display for more than 3 minutes, but each signal message will be displayed whenever you turn on the lamp. Lamp is not well attached If the LED blinks rapidly, it indicates that the lamp is not attached properly. Temperature is too high If the projector's internal temperature is too hot to operate safely, the LED will blink slowly for one minute and then the lamp will turn off automatically. Normal status If the LED light is off, it means the lamp and temperature inside the projector are normal. Caution: The lamp indicator will light up when the lamp becomes too hot. Turn off the power and let the projector cool for 45 minutes, then turn it on again. [. . . ] Press the button again, and the image will be further magnified (to a maximum of 4X). Press the magnify "-" button, and the size of the magnified image will be reduced by 50 percent. To return to the normal display mode, press the "Return" button. If users connect the PS2 (ADB) mouse cable on the projector with the PC/Notebook (Macintosh/ Powerbook) mouse port, the disk pad will be able to function as a PC/Notebook (Macintosh/ Powerbook) mouse. [. . . ]