User manual BENQ P211 Document

[. . . ] No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Benq Corporation. Disclaimer Benq Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Benq Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of Benq Corporation to notify any person of such revision or changes. ii Reference Fill in here!! For the convenience of service, write following related information of your monitor in the space below. The serial number is on the back of the product. Monitor Information Product Name: Serial Number: Date of Purchase: Dealer Information Dealer: Telephone: Number: Address: iii Safety Safety Instructions ! The AC plug isolates this equipment from the AC supply. Slots and openings in the cabinet and the back or bottom are provided for ventilation. [. . . ] 4 Consult the dealer or an experienced radio/television technician for help. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution: 1 If you find some parts of the monitor display discolored due to magnetic fields generated by electrical facilities or appliances, turn off the monitor for at least 15 minutes. The degaussing circuit of the monitor will eliminate the discoloration. 2 Do not remove the monitor from its swivel base while the power is on to prevent discoloration. If discoloration occurs, follow the above-mentioned procedure for adjustment. 3 Shielded power cord and interface cable, if any, must be used in order to comply with the emission limits of FCC Class B digital device. ix CE Declaration CE Declaration This monitor complies with 72/23/EEC and 89/336/EEC modified by 92/31/ECC. No re-configuration or adjustment is needed when a user changes display mode. Benq P211 is not only in compliance with MPRII, but also meets strictest low radiation regulations of "MPRII" and "TCO'99". Benq P211 is produced by the ISO 14001 certified manufacturer, and in compliance with the global environmental labelling scheme TCO'99 which covers not only standards regarding emissions, energy efficiency, electrical and fire safety, but also ergonomic qualities, and ecological concerns. Supporting VESA DDC 2BTM standards, Benq P211 is compatible with Plug'n Play feature of Windows® XP/ ME/ 2000 / 98 / 95. Wide Range AutoScan i key (Fuzzy Auto calibrating) Low radiation Users and Environment Plug'n Play Compatibility 2 Unpacking the Package Power Management The Power management of this monitor complies with these VESA power saving modes: Mode Power Consumption < 150W Max. < 5W < 5W < 5W Horizontal Vertical Syne Sync On Off On Off On On Off Off LED On Stand-by Suspend Off Green Amber Amber Amber Factory Preset Timings Resolution 640 x 400 640 x 480 800 x 600 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1600 x 1200 1600 x 1200 1920 x 1440 Vertical Frequency (Hz) 70 60 75 75 85 75 85 75 85 75 Horizontal Frequency (KHz) 31. 47 31. 47 46. 88 60. 02 68. 68 79. 98 91. 15 93. 75 106. 00 112. 50 ** All above timings are non-Interlace timings. 3 Chapter 2 Chapter 2 Installing the Monitor This monitor is equipped with an autosensing universal compatible power supply for voltage ranges 100-120/200-240V AC, 50~60Hz. . Please confirm the line voltage designation at the rear panel of the monitor before connecting the machine. 1) Make sure that the system power is turned off. 2) Please refer to the instructions below to connect the signal cable through D-SUB or BNC. 3) Connect the power cord to the monitor and attach it to power source. 4) Turn on the computer and the monitor. 4 Installing the Monitor Connecting the Signal Cable Your Benq P211 provides both D-SUB and BNC signal connectors. The D-SUB or BNC signals can automatically be detected by its microprocessor. Connecting through D-SUB signal connector 1) Make sure that the system power is turned off. 2) Connect the computer end of the D-SUB cable to the 15-pin output connector on the video board of your computer. 3) Connect the monitor end of the D-SUB cable to the D-SUB receptacle on the back of the monitor. 5 Chapter 2 Connecting to An Apple If you connect the monitor to an Apple Macintosh through a D-Sub cable, you need to add the Macintosh adapter to connect the video signal port of your computer and the monitor signal cable. Before connecting the adapter please refer to the user's guide of the adapter to set the switches of the adapter. 6 Installing the Monitor Connecting through BNC Signal Connector 1) Make sure that the system power is turned off. 2) Connect the computer end of the BNC cable to the output connector on the video board of your computer. 3) Connect the monitor end of the BNC cable to the BNC receptacle on the back of the monitor. 7 Chapter 3 Chapter 3 A Look at the Control Panel Menu key : enters or changes Main menus. & key : scrolls the light coloured bar up or down and represents HOT KEY for brightness adjustment. & key : scrolls the light coloured bar left or right and represents HOT KEY for contrast adjustment. i key : is used for Fuzzy Automatic calibration adjustment. 8 A Look at the Control Panel Making Adjustments i key (Fuzzy Auto Calibration ) Just push the i key, then the monitor will automatically adjust display's size and position to the optimum. No re-configuration or adjustment is needed when a user changes display mode. "Reset" function for display's geometry, size and position only works under the factory preset timings (please see page 3). [. . . ] It is especially noticeable when using a light-gray or every-otherdot pattern. Moire can be reduced by adjusting the iscreen moire reduction function. Prior to adjustment, set the screen to a full white pattern so that moire will be visible. After this adjustment, make changes to a different screen background in order to reduce moire even further. [. . . ]