User manual BENQ MP624

[. . . ] MP623/MP624 Digital Projector User Manual Welcome Table of contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction. . . . . . . . . . . . . . . . . . . . . . . . 7 Projector features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Personalizing the projector menu display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Shutting down the projector . . . . . . . . . . . . . . . 40 Menu operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Maintenance. . . . . . . . . . . . . . . . . . . . . . 49 Care of the projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Lamp information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Positioning your projector13 Choosing a location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Obtaining a preferred projected image size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Troubleshooting . . . . . . . . . . . . . . . 56 Specifications . . . . . . . . . . . . . . . . . . . . 57 Projector specifications. . . . . . . . . . . . . . . . . . . . . . . . 57 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Timing chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Connection . . . . . . . . . . . . . . . . . . . . . . . 17 Connecting a computer or monitor. . . [. . . ] Press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image. Press / . Press / . Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Press the key repeatedly until the picture size is suitable for your need. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. When the key is pressed again, the picture is further reduced until it is restored to the original size. Press Menu/Exit and then press / until the DISPLAY menu is highlighted. Repeat steps 2-4 in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps. Press on the projector repeatedly to magnify the picture to a desired size. To navigate the picture, press Mode/Enter to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture. 30 Operation 6. To reduce size of the picture, press Mode/Enter to switch back to the zoom in/out functionality, and press AUTO to restore the picture to its original size. You can also press repeatedly until it is restored to the original size. The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details. Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is): 1. Press Menu/Exit and then press / until the DISPLAY menu is highlighted. Press / to select an aspect ratio to suit the format of the video signal and your display requirements. About the aspect ratio In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most 16:10 picture use of the screen without altering the image's aspect ratio. 15:9 picture 2. Real: The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized 4:3 picture to full screen. You could move the projector towards the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments. 16:9 picture 3. 4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. [. . . ] Select the correct input signal with the Source key on the projector or remote control. Open the lens cover. Blurred image Cause The projection lens is not correctly focused. The lens cover is still closed. Remedy Adjust the focus of the lens using the focus ring. Adjust the projection angle and direction as well as the height of the unit if necessary. [. . . ]