User manual BENQ FP567

[. . . ] Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any above mentioned misuse or other accident (dropping, mis-operations) occurs, contact qualified service personnel for servicing. The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. Disclaimer Safety Instructions English 1 Benq LCD Color Monitor User's Guide Table of Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If they are missing or are damaged, please contact the dealer immediately at which you purchased the good. LCD monitor with undetachable signal cable Quick Start Guide CD-ROM Power cord Audio cable Extension Base English 3 Benq LCD Color Monitor User's Guide Views of the Monitor Front View Back View (1) English 4 Benq LCD Color Monitor User's Guide Back View (2): Locations of plugs & sockets 1. Power cord English 5 Benq LCD Color Monitor User's Guide Installation Hardware Installation A. Make sure that the computer and monitor's power are both turned off. Connect the signal cable to the VGA output of the graphics card on the computer. Connect the power cord at the back of the monitor to an AC power socket. Please make sure that the socket is not blocked or covered, so you can disconnect the unit from AC supply if you need to. Your monitor is equipped with an automatic power supply for a voltage range from 100 to 240 Volt at a frequency of 50 to 60 Hz. If you are unsure, ask your electricity supplier. Signal Power cord Audio cable English 6 Benq LCD Color Monitor User's Guide Adjusting the Monitor A Look at the Control Panel ikey Exit < > Enter There are 6 keys for user's control including "iKey", "Exit", "Enter", "<" and ">" key and a power swith. The following descriptions are the introduction of these keys & switch. "iKey" : Adjust vertical position, phase, horizontal position and pixel clock automatically. "Exit" key: Back to main menus, save menu or exist OSD menu without saving. Right key is the hot key for Brightness adjustment. Hot Key Mode Contrast hot-key 1. The adjustment can be auto-saved. English 33 Benq LCD Color Monitor User's Guide Volume hot-key 1. The adjustment can be auto-saved. Main Menu Mode Control Functions Available in Main Menu 1. Luminance Press "<"or ">" key to select this item and press "Enter" to enter sub-menu. There are two items for luminance adjustments. Brightness: adjust the brightness of the display. Contrast: adjust the difference between the light and dark areas. English 34 Benq LCD Color Monitor User's Guide 2. Geometry Press "<"or ">" key to select this item and press "Enter" to enter sub-menu. (Horizontal) Position: adjusts the horizontal position of the display. V. (Vertical) Position: adjusts the vertical position of the display. Phase: adjusts the phase of pixel clock. Pixel Clock: adjusts the frequency of the pixel. English 35 Benq LCD Color Monitor User's Guide 3. Color Adjustment Press "<"or ">" key to select this item and press "Enter" to enter sub-menu. There are four items for color adjustments. There are three items to adjust. Press "<"or ">"key to select a color and press "Enter" to adjust color temperature. 4. Miscellaneous Press "<"or ">"key to select this item and press "Enter" to enter sub-menu. [. . . ] If the image is still not correct and the OSD also has a fault colour appearance, then one of the three primary colours is missing in the signal input. If any pins are bent or broken off, then contact your dealer or read the chapter, Additional Help, Repairs & Service. No image can be seen:  Is the prompt on the display illuminated in green?If the LED is illuminated in green, then press the "Exit" button on the monitor to access the On Screen Display. [. . . ]