User manual BENQ ESG104 DOCUMENT

[. . . ] BENQ_ESG103QG_E. book Page i Tuesday, July 30, 2002 8:45 PM Table of Contents Introducing ESG103 / ESG104 Broadband Router . 6 i BENQ_ESG103QG_E. book Page ii Tuesday, July 30, 2002 8:45 PM ii BENQ_ESG103QG_E. book Page 1 Tuesday, July 30, 2002 8:45 PM Introducing ESG103 / ESG104 Broadband Router Congratulation on your purchase of the BenQ ESG103 broadband routers / ESG104 Security Gateway. With ESG103/ESG104 you will be able to share a single Internet connection with multiple network-connected laptops and desktop computers. [. . . ] Use one RJ-45 Category-5 cable to connect the ADSL / cable modem's LAN port to the ESG103/ESG104's WAN port. A Setup Your ESG103/ESG104 ADSL/Cable Modem 2 BENQ_ESG103QG_E. book Page 3 Tuesday, July 30, 2002 8:45 PM 3. Use another RJ-45 Category-5 cable to connect one of the ESG103/ESG104's LAN ports and the Ethernet port to your PC. English 4. 5. Plug in ESG103/ESG104 power adapter and connect the power supply to the PWR/DC port on the back panel. ESG103/ESG104's power LED should be green then blink in this sequence: WAN, 1X, 2X, 3x, and 4X. Follow the instructions to make sure settings are correct and restart your PC. B 1. Before Setting Your ESG103/ESG104 (Please make sure your PC can obtain an IP address automatically. ) For Win98/ME Users Click Start > Settings > Control Panel. The Control Panel window will appear 2. Double-click on Network icon. The Network dialog box will pop up. 3 BENQ_ESG103QG_E. book Page 4 Tuesday, July 30, 2002 8:45 PM English 3. Under the Configuration tab, select the TCP/IP of your network card and click on the Properties button to bring up the TCP/IP Properties dialog box. 4. Click OK again to save the configuration, and reboot your PC. For Windows 2000/NT Users 1. The Local Area Connection Proper ties dialog box will appear. 4 BENQ_ESG103QG_E. book Page 5 Tuesday, July 30, 2002 8:45 PM 3. In the Local Area Connection Properties window, click Internet Protocol (TCP/IP) then click Properties at the bottom of the window. English 4. Click OK again to save the settings and reboot your PC. For Windows XP Users 1. The Network and Internet Connection window will pop up. 3. Double-click the Local Area Connection icon at the bottom of the window. The Local Area Connection window will pop up. 5 BENQ_ESG103QG_E. book Page 6 Tuesday, July 30, 2002 8:45 PM English 4. Right-click on the Local Area Connection Enabled icon and a pop-up menu will appear. 6. Select Internet Protocol (TCP/IP) and click on the Properties button below it. Click OK to close the Local Area Connection Properties window and reboot your PC 1. C Connect to Your ISP After rebooting your PC, start up a web browser such as the Internet Explorer or the Netscape Communicator, and type 192. A welcome web page will be shown in your browser as an indication that your PC and the ESG103/ESG104 might not be able to communicate with your PC normally. Please refer to Appendix D in the User's Guide. Note: If you connect to the Internet through a proxy server, please remember to remove the proxy server settings from your web browser. Otherwise, the ESG103/ESG104 may not be able to communicate with your PC normally. Please refer to Appendix D in the User's Guide. 6 BENQ_ESG103QG_E. book Page 7 Tuesday, July 30, 2002 8:45 PM 2. A login dialog box will appear, asking you to key in an administrator's ID and password. [. . . ] 9. After about 10 seconds, the router will restart automatically and the whole installation process is complete. Go to your favorite website to confirm that the installation has completed successfully. If you cannot yet view the website, please repeat the procedures described in section C. 10 [. . . ]