User manual BENQ DV3250

[. . . ] English DV3250 LCD Display User's Manual Welcome Copyright English Copyright BenQ Corporation. No part of this User's Manual may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Disclaimer BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents of this User's Manual. BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes. Important Safety Instructions Electrical energy can perform many useful functions, but it can also cause personal injury and property damage if improperly handled. [. . . ] Open the lid of the remote control battery compartment (slide the lid backward while pressing down. ) 2. Ensure that the batteries are inserted with the positive and negative terminals in the correct direction corresponding to the (+) and (-) marks in the battery compartment. 3. Press down on the lid of the battery compartment and gently push it back into position until it is firmly seated. Notes on Using Batteries The use of the wrong type of batteries may cause chemical leaks and/or explosion. Please note the following: · Always ensure that the batteries are inserted with the positive and negative terminals in the correct direction as shown in the battery compartment. Mixing old and new batteries will shorten battery life and/or cause chemical leaks from the old batteries. · Chemicals which leak from batteries may cause skin irritation. If any chemical matter seeps out of the batteries, wipe it up immediately using a dry cloth. · Due to varying storage conditions, the battery life for the batteries included with your display may be shortened. If the remote control is not used for a long period of time, remove the batteries. Remote Control 15 Using the Remote Control English 16 Power on, Power off and Standby Turning on the display 1. After the power cord is plugged into a wall outlet, the display will turn on and enter standby mode automatically, and the power indicator will light up in red. Press the button on the display, or press the POWER button on the remote control. The display will turn on, and the power indicator will light up in green. If the set is already connected to a signal source, the display will display that signal. Turning off the display Press the button on the display again, or press the POWER button on your remote control again, and the display will go into standby mode. (The power indicator will turn red). Switching Inputs INPUT 1. Turn on all connected equipment or computers. Press the INPUT button on your display or press the INPUT button on your remote control to select input signal. The sequence is as follows: TV -> AV1 ->AV1-S-> AV2 -> AV2-S->AV3->AV3-S->Component 1-> Component 2->PC->DVI->TV. . . AV1-S, AV2-S or AV3-S will appear only when the SVideo input of AV-1, AV-2 or AV-3 is connected. Using the Remote Control Adjusting Volume English Adjusting the volume 1. Press the VOL button on your display or press the VOL button on your remote to increase volume. Press the VOL button on your display, or press the VOL button on your remote to decrease volume. Press the MUTE button on your remote control to temporarily cut off the sound. Press the MUTE button once more, or press the VOL or Power button on your display or the remote control to restore the sound level. MTS (TV Sound selection) Press the MTS button on your remote control to toggle among "Stereo", "SAP (Second Audio Program)", or "Mono" reception. MUTE MTS Changing Channels Using the Channel selection buttons on the Remote Control to Change Channels · To select a single- or double-digit channel, press the corresponding channel selection buttons on the remote control. [. . . ] and there is a loss of definition · The DVD player is set for a high-level output. in the brightest areas of the · The AV video signal has not been terminated properly image. The image appears too 'washed · Reduce the brightness level till the black areas of the picture out', or the darkest areas of the appear as black. Power indicator lamp flashes · This indicates the PC/DVI input has been selected with no red. [. . . ]