User manual AOPEN S661FXM7S

[. . . ] Table of Contents Table of Contents 1. 1 A Thank-you Note Before You Get Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 2 Features of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 2 Introduction to This Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 1 How does your motherboard look like?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 2 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. 3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 3 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 1 Quick Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 2 Installation You Have to Know. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Installing CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To enable LAN wakeup function, you have to set the "Wake on PCI Card" enable in the BIOS "Power Management Setup" section. Speed LED (Left) Green 100Mbps ACT LED (Right) Yellow 21 Connecting USB2. 0 This motherboard provides eight USB 2. 0 ports to connect USB devices such as mouse, keyboard, modem, printer, etc. You can also use proper cables to connect Front USB connector to USB modules or chassis front panel. Pin 1 Pin 1 12 +5V SBD6SBD6+ GND KEY 9 10 +5V SBD7SBD7+ GND NC USB Connector 22 Connecting S/PDIF S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which provides impressive audio quality through optical fiber and allows you to enjoy digital audio instead of analog audio. Through a specific audio cable, you can connect the S/PDIF connector to other end of the S/PDIF audio module, which bears S/PDIF digital output. Normally there are two S/PDIF outputs as shown, one for RCA connector, the most common one used for consumer audio products, and the other for optical connector with better audio quality. Same as outputs, you can also connect RCA or optical audio products to input connectors on the module and have the voice or music come out from your computer. However, you must have a S/PDIF supported speaker/amplifier/decoder with S/PDIF digital input/output to connect to the S/PDIF digital input/output to make the most out of this function. Pin 1 (RCA) S/PDIF OUT S/PDIF IN S/PDIF OUT S/PDIF IN (Optical) S/PDIF Cable S/PDIF Module 23 Super 5. 1 Channel Audio Effect This motherboard comes with an AC'97 CODEC, which supports high quality of 5. 1 Channel audio effects, bringing you a brand new audio experience. On the strength of the innovative design of AC'97 CODEC, you're able to use standard line-jacks for surround audio output without connecting any external module. To apply this function, you have to install the audio driver in the Bonus Pack CD as well as an audio application supporting 5. 1 Channel. Picture below represents the standard location of all speakers in 5. 1 Channel sound tracks. Please connect the plug of your front speakers to the green "Speaker out" port, rear speakers' plug to the blue "Line in" port and both of the center and subwoofer speakers to the red "MIC in" port. 24 Connecting Front Audio If the housing is designed with an audio port on the front panel, you'll be able to connect onboard audio to front panel through this connector. By the way, please remove the jumper cap from the Front Audio Connector before you connect the cable. Do not remove this yellow jumper cap if your housing doesn't have an audio port on the front panel. Pin1 1 AUD_MIC AUD MIC BIAS AUD_FPOUT_R NC AUD_FPOUT_L AUD_GND AUD_VCC AUD_RET_R KEY AUD_RET_L Front Audio Connector 25 Connecting CD_IN This connector is designed to connect CD Audio cable from CDROM or DVD drive to onboard sound. R GND GND L CD-IN Connector 26 Connecting AUX_IN This connector is used to connect MPEG Audio cable from MPEG card to onboard sound. R GND GND L AUX-IN Connector 27 Colored Coded Back Panel The onboard I/O devices have PS/2 Keyboard, PS/2 Mouse, RJ-45 LAN Connector, COM, VGA port, Printer, USB, and AC'97 sound ports. The view angle of drawing shown here is from the back panel of the housing. PS/2 Mouse Connector USB 2. 0 Ports SPP/EPP/ECP Parallel Port RJ45 LAN Jack Line-In Speaker Out MIC-In PS/2 Keyboard Connector COM Port VGA Port USB 2. 0 Ports PS/2 Keyboard: PS/2 Mouse: USB Port: Parallel Port: COM Port: RJ-45 LAN Port: VGA Connector: Speaker Out: Line-In: MIC-In: For standard keyboard, which use a PS/2 plug. For Microphone 28 LED Indication LED indication including Standby LED and AGP LED are AOpen's considerate designs that aim at providing you friendly system information. STBY LED will light up when power is provided to the motherboard, giving you a convenient indication check the system power status in circumstances such as power on/off, stand-by mode and RAM power status during Suspend to RAM mode. AGP LED aims to protect your motherboard from being damaged by over voltage of AGP card. When AGP Protection Technology is implemented, this motherboard will automatically detect the voltage of AGP card and prevent your chipsets from being burnt out. Please note that if you install an AGP card with 3. 3V, which is not supported by SiS 661FX chipset, the AGP LED on the motherboard will light up to warn you the possible damage of the exceeding voltage. STBY LED AGP LED 29 3. 4 Jumper Settings JP28 Keyboard / Mouse Wakeup Jumper This motherboard provides PS2 keyboard / mouse wake-up function. JP28 Keyboard / Mouse Wakeup Jumper 1 1 Disable Enable JP14 Clear CMOS Jumper 1 Clear CMOS 1 Normal You can clear CMOS to restore system default setting. Connect ATX power cable back to connector PWR2. 30 Chapter 4 Special Features and Utilities Chapter 4 Special Features and Utilities RAID (Redundant Array of Independent Disks) With the latest chipsets implemented, SiS 964 provides RAID 0 and RAID 1 function for the Serial ATA hard disks. You may use RAID BIOS Setting Utility provided by SiS to setup your disk array. For more RAID introduction, please visit our website: http://english. aopen. com. tw/tech/techinside/RAID. htm RAID BIOS Setting Utility (for s661FXm-7S only) In order to make sure your system can recognize and operate Serial ATA RAID device smoothly, we have to enter RAID BIOS Setting Utility to do some configuration. After finishing the BIOS setup and reboot, you will see [Press <CRTL><S> to run BIOS Setting Utility] about half way through the boot up. [. . . ] Without wizards or steps, all you have to do is to do one click and then it's done. After putting in the CD, you will be prompted with AOpen welcome page and our branches information. First, click on the install driver ICON at left side for necessary drivers. Second, click on the install utility ICON at left side for preferred utilities. [. . . ]