User manual AKG HEARO 888 TITAN

[. . . ] You can operate your transmitter with several digital headphones simultaneously. Make sure to use digital wireless headphones operating in the same UHF frequency band as the HEARO 888 TITAN. 2 IVA - Individual Virtual One drawback of headphone listening is the psychoacoustic phenomenon of "inside localAcoustics ization": the orchestra seems to play inside your head rather than in the room. AKG developed a binaural audio processing techniquecalled IVA (Individual Virtual Acoustics) that models the way the head and pinnae change the arriving sound waves (ear matching function). [. . . ] Before connecting the transmitter to your audio source, switch the audio source OFF. Use the supplied RCA cable to connect the white LINE OUT L or REC OUT L jack on your audio source to the white INPUT L jack (15) on the transmitter rear panel and the red LINE OUT R or REC OUT R jack to the red INPUT R jack (15). 3 Connecting to TAPE By connecting your HEARO 888 TITAN to the "TAPE" or "PLAYBACK" inputs on your ampliInputs fier, you can enjoy IVA and surround sound through an extra pari of wired headphones in addition to the wireless `phones. Use the supplied RCA cable to connect the white LINE OUT L or REC OUT L jack on Your audio source to the white INPUT L jack (15) on the transmitter rear panel and the red LINE OUT R or REC OUT R jack to the red INPUT R jack (15). Use another RCA cable (not supplied) to connect the white "TAPE IN" or "PLAYBACK IN" jack on the amplifier to the white OUTPUT jack (16) on the HEARO 888 TITAN rear panel and the red "TAPE IN" or "PLAYBACK IN" jack on the amplifier to the red OUTPUT jack (16) on the HEARO 888 TITAN rear panel. Connect your wired headphones to the headphones jack on your amplifier. Refer to the operating manual of your amplifier for instructions on how to listen to and disable the signal at the TAPE" or "PLAYBACK" input. On most amplifiers, you can push the "TAPE MONITOR" switch IN to listen to the processed signal and OUT to cut the processed signal. In this mode, the loudspeakers will also reproduce the processed signal present at the Important: headphones output. Since IVA and/or surround processed signals are not loudspeaker compatible, mute the loudspeakers while listening through headphones. In order to ensure the longest possible service life for the rechargeable batteries, we deliver 4. Therefore, charge the supplied batteries before first operating in the Headphones your headphones system. The supplied batteries have been inserted into the headphones for your convenience. If you operate the headphones on dry batteries, never try to charge the WARNING: batteries using the transmitter's charging feature. The CHARGE LED (7) on the transmitter will light red to indicate that the batteries in the headphones are being charged. If signal is present at the transmitter audio input, the CHARGE LED (7) will light orange. You may leave the headphones on the transmitter for as long as you like without risking to overcharge the batteries. In order to maintain full battery capacity for as long as possible, discharge the batteries Important: completely about once a month: Switch the headphones on and leave them outside the transmitter until the POWER LED (2) extinguishes. 2 Replacing Batteries to recharge the supplied batteries more often than would be convenient, you may consider replacing the batteries with new AAA size 1. Make sure to align the batteries with the polarity marks inside the battery compartment. Replace the ear pad on the earphone aligning the four pins on the ear pad with the matching openings in the earphone base plate. Note that the transmitter will not switch on until it detects an audio signal at the INPUT L/R jacks (15). [. . . ] For physical reasons that are not related to the quality of the product, extremely strong interference sources may affect reception. In order to maintain interference-free listening pleasure, do not operate your HEARO 888 TITAN in the close vicinity of radio equipment, cellular telephones, or directly above TV or computer monitor picture tubes. The supplied connecting cables are long enough to allow the transmitter to be placed at a safe distance from interference sources. Interference caused by other users of the 914, 434, or 864 MHz LPD band are beyond AKG's control. [. . . ]