User manual AKG CS5 CONFERCONTROL

[. . . ] CS5 ConferControl Computer based Controlling Program for Conference System CS5 User Manual AKG Acoustics CS5 ConferControl Computer based Controlling Program for Conference System CS5 Copyright All rights reserved!No part of this User Manual can be copied, forwarded or translated without the written permit of the author (AKG Acoustics). June, 2009 Version: 1. 5 Contents 1. INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] CHIPCARD (D. 8. ) In window «Settings» (D. ) (see Diagram 12) after pushing the «hipcard» button (D. 8. ) the following window opens (see Diagram 13) on the next page. 22 D. 8. 2. D. 8. 1. D. 8. 3. D. 8. 4. D. 8. 5. Diagram 13: «Chip card» window (D. 8. ) The following functional options are available: 4. 4. 8. 1. Table of Chipcards (D. 8. 1. ) The address of those units can be seen here into which a chip card has been inserted and were connected to the system. The left side column of the table contains the unit addresses of the delegate units, while the right side column shows the identification number of the chipcard inserted into the given unit. When the chipcard is pulled out from the unit the line containing the address of the given unit and the identification number of the card pulled out is deleted. When a chipcard is inserted a new line appears in the table, in which the address of the given unit and the identification number of the inserted card can be seen. Chipcard number (D. 8. 2. ) After selecting a line from table (D. 8. 1. ) in the field of «Card number» (D. 8. 2. ) the identification number of the card included in the selected line is displayed. Buttons «Read» (D. 8. 3. ) and «Write» (D. 8. 4. ) are activated simultaneously. and D. 8. 4. ) With the aid of press button «Read» (D. 8. 3. ) it is possible to read the identification number of the card inserted into the card reader of the unit selected from the table (D. 8. 1. ). For changing the identification number of the card the appropriate number has to be entered with the keyboard into the «Card number» (D. 8. 2. ) field, then button «Write» (D. 8. 4. ) has to be pressed. At this point the old card number is deleted and the new number is recorded, and it is simultaneously displayed in the table (D. 8. 1. ). 23 Attention!During re-writing the identification number of the card it is strictly forbidden to remove the card from the unit. Exit (D. 8. 5. ) With clicking on button «OK» (D. 8. 5. ) it is possible to return to the «Settings» (D. ) page of the «Conference controlling program» window (Diagram 12). After getting connected to the conference system, but before loading the current conference, it is possible to enter or re-enter the number of the chipcards. LANGUAGE EDITOR (D. 9. ) With the aid of this press button it is possible to generate the controlling program in any arbitrary language. It is possible to execute here the rewriting or modifying of all the labels that are displayed on the screen, in line with the demand of the user. In order to activate the language editor push the «Language Editor» button (D. 9. ) in the «Settings» page (D. ). D. 9. 6. Diagram 14: «Language Editor» window (D. 9. ) 24 With the aid of this menu a controlling program of an arbitrary language may be created. This is the place where it is possible to change or edit the words and expressions that are used in the existing controlling program. Source language (D. 9. 1. ) It is possible to select here from the roll-down list the source language that serving as the basis of the new language to be created. There are three different languages (English, Russian and Hungarian) asfactory defaults. After selecting the appropriate source language the words belonging to the given language are displayed in table (D. 9. 3. ). Destination language (D. 9. 2. ) It is possible to select from the roll-down list either the new language which is to be created or a language already existing. [. . . ] For this end first the Basic Unit (BU) of the conference system should be switched off. Switch on the controlling computer, on which controlling program CS5 Confer Control had been installed already previously according to the contents of Section «3. It is not needed to start the controlling program itself for the time being. Connect the «USB» cable delivered for the system to both the computer and the basic unit (BU) of the conference system, then switch on the power supply unit. [. . . ]