User manual AEG-ELECTROLUX 713

[. . . ] Cut off the power position when making and adjustments in the needle area. Always unplug the sewing rnachine from the electrical outlet when removing covers, lubricating, or when making any other user service adjustments mentioned in this instruction manual. 1 Reverse button 1 Reverse button 2 Pattern selection dial 2 Pattern selection dial 3 Stitch length selection dial 3 Stitch length selection dial 4 Bobbin winder stopper 4 Bobbin winder stopper 5 Bobbin spool 5 Sewing pin 6 Spool pin 6 Spool pin 7 Winder tension disc 7 Top cover 8 Thread retainer 8 Thread retainer 9 Thread take-up lever 9 Thread take-up lever 10 Thread tension disc IO Thread tension disc 11 Bulb cover 12 Presser foot presser 11 Bulb cover 13 Ripper foot presser 12 Presser 14 Sewing foot 13 Ripper 15 Needle Plate 14 Sewing foot 16 Extendable cloth plate 15 Needle Plate 16 (accessoriescloth plate Extendable case) 17 Handle (accessories case) 18 Balance Wheel l7 Handle 19 Power Wheel 18 Balance 20 Foot Controller receptacle 19 Power 21 Needle clamp screw 20 Foot Controller receptacle 22 Needle clamp plate 2I Freearm cloth screw 23 Presser foot lever 22 Freearm cloth plate 23 Presser foot lever Space while sewing but also can be easily disassembled. Avoid cloth piled up in front of needle while sewing pockets, tucks and waist edges. [. . . ] While doing straight stitching, both upper and lower threads must be knotted between the two layers of garment. (1) Regulated indicator (2) The smaller the tension of upper thread is bigger, turn up the indicator. In order to achieve good effect of zigzagging, the tension of upper thread should be less than that of straight stitching. Needle is pulled out from fabric and the desired size of stitching should he selected on the selection dial. As for stitching Double Action stitching, its length should be adjusted into "(1)-(10)". With the following adjustment, the length of stitchcould be selected as you like. Selection dial 2 and 3 should be different as shown in illustration Model 713 / 723). " is the correct range of adjustment for making buton holes -Range from 0. 5 to 4 could be used for zigzag stitching -The correct elastic stitch value should be "(1)-(10)" How to make the elastic stitch better?In case the elastic stitch turns out to be unsatisfactory, you may turn the selection dial to " - " and in this way, stitches would be thicker while turning to "+" they would be more sparse. If the reverse button is always pressed down, the machine will do reverse stitching all the time. (1) Life the cover (1) Cover (2) Lower the feed dog by pulling down the shaft and moving it towards the direction inclicated by the arrow head as shown in the illustration. (2) Lower teeth lever (3) Raise the feed dog by pulling down the lower teeth lever and moving it towards the direction indicated and reach "A" by the arrowhead as shown in the illustration. And its pressure drops to " 2 " when sewing appliques, mesh fabrics and embroidery. As for chiffon, lace, yarn and other miscellaneous fine materials, you may put the dial to " 3 ". 5 - 4 (3) presser foot for needlework: zigzag (4) pressure of thread tension disc: 2-6 Raise presser foot and put cloth beside leg wire of needle plate. Turn forward the balance wheel and lower the needle down into the fabric. Fabric will go along leg wire and is carned forward automatically by feed dog. In order to make end of thread firm, please press the reverse stitch buton and do several reverse stitches. Stop the machine, and turn the balance wheel to bring the needle down into the fabric. [. . . ] Take out the pendular shuttle: Raise needle to its highest position and lift shuttle Gover. Remove the bobbin case from the machine, Uncover shuttle lever and draw out the shuffle retaining ring. Instruction: clean the feed dog with a brush and soft and dry rag (1) Bobbin case (2) Shuttle lever (3) Shuttle retaining ring (4) Pendular shuttle (5) Shuttle carrier Installation of the pendular shuttle: hold shuttle center pin and fit carefully black into the shuttle carrier. Refit shuttle retaining ring and make sure that the following Center pin is fixed in the Slot of the shuttle canier. [. . . ]