Detailed instructions for use are in the User's Guide.
[. . . ] Power On/Off Connect it to your other equipment Audio I/O This manual, as well as the software and hardware described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice and should not construed as a commitment by Kemper Digital GmbH. Kemper Digital GmbH assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, recording, by smoke signals or otherwise without the prior written permission of Kemper Digital GmbH. [. . . ] Once you have selected the right location for your new patch, you may want to give it a new name. Use the Value knobs or buttons to select the desired letter or symbol, and move through the characters with the PARAMETER buttons. Once you are satisfied with the name, press STORE again to complete the process. If you are in Single mode, press STORE to send the Single patch to your external device. If you are in Multi mode, press STORE to send the Arrangement (this contains all the patch information for each Part). If you only want to send the Single patch of the currently selected Part, select "Dump Single" instead of "Arrangement" and press STORE to send it. If you are in Multi Mode when you enter the Store menu, it will be assumed that you wish to store the current Multi setup. Select the Multi slot you wish to use and follow the same proceedure as when storing a Single patch. If you are in Multi mode and want to store the single patch of the current Part, select "Store Single Menu" from the list of options under "Function". If you are in Sequencer mode (or Virus Control mode) and wish to copy all of the single patches to the Multi mode edit buffer, select "Multi Edit Buffer" from the list of options under "Function". If you suddenly realise that you are about to overwrite your favourite patch and decide to bail out, press EXIT at any time to get straight back out of the Store menu. In this menu, you will find all the global parameters which determine the overall behaviour and feel of the Virus TI Snow, such as the brightness of the LEDs or the behaviour of the knobs etc. Please refer to the reference manual for details on the different functions within this menu. Don't worry none of them is the equivalent of a self-destruct button, and you can always reset them all to their default values by pressing and holding TAP TEMPO while you power up the Virus, should you feel you've messed something up. So, how many voices (notes) can you expect from the Virus TI Snow at a time?The answer is that since the Virus TI sound engine is highly dynamic, the voice count can vary dramatically from one sound to the next, depending on which features are being used. To help give you a rough idea of how many voices you can expect to achieve with your chosen patch, we have provided a patch complexity meter in the top right hand side of the display. There are five levels of complexity, with level 1 being the least complex, and hence allowing for the highest voice-counts. Since it would be too complicated to explain all the different scenarios, we have provided the following three examples*: *The examples below assume Single mode operation, or playing one part at a time in Multi mode. Using additional parts simultaneously might affect the amount of voices you can achieve. 1 or 2 simple oscillators, one or two mod routings and one or two effects can achieve upwards of around 32 voices. With the very simplest of patches you can achieve far more than this - for example, please check out RAM1- 78, a nice, warm PWM pad with Delay and Chorus, capable of being played with more than 50 simultaneous voices. [. . . ] NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class , , B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in residental environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the user manual, may cause interference harmful to the operation of other electronic devices, Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determinated by turning the unit , , OFF" and , , ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. [. . . ]